1stGen.org

THE place for 1st gens

Skip to content

New first gen owner from MN

Stop in and say hi

Moderators: Greenleaf, BC847, Richie O

Post a reply

New first gen owner from MN

Postby Tx9h6e4cuda » Sun Oct 26, 2014 4:28 pm

Hello, I am new here and the diesel world. I just bought my first Cummins diesel truck. Its a 1992 Dodge 3/4 ton 2wd, 5 speed. Its a rough truck (body super rusty) but the engine runs super nice. I think I might be rebodying it and drive the snot out of it. Hope to learn alot from everyone.

Image

Image

Image
Tx9h6e4cuda
smoke screw?
 
Posts: 1
Joined: Sun Oct 26, 2014 4:14 pm
Top

Re: New first gen owner from MN

Postby RCCUMMINS89 » Sun Oct 26, 2014 7:29 pm

Welcome
89 RC on shortened 92 diesel frame - NV4500 w/dual disc/4.10s on 37s. - Self built pump, "hot screw", lots of timing, True high volume low pressure lift pump, 62fmw/68/.7gated, 77lpm SAC Inj., Studs/O-rings,- 423/1220 Mustang - 11/16/2013 http://www.TheHungryDiesel.com full line dealer, if you don't see it please ask.
RCCUMMINS89
14mm rotor
 
Posts: 4826
Joined: Mon Oct 03, 2011 4:19 pm
Location: Spirit Lake, ID
Top

Re: New first gen owner from MN

Postby ellis93 » Sun Oct 26, 2014 7:34 pm

Welcome
93 D250 ,5 speed,4.11s,k&n autometer tach pyro trans boost guages,GDS 60mm h1c 14cm,honed 5x10,hplp/reg,1/8 timing,M+H M2 fuel pin, tims cooler tubz
User avatar
ellis93
14mm rotor
 
Posts: 7762
Joined: Wed Feb 17, 2010 3:16 pm
Location: lucedale,mississippi
Top

Re: New first gen owner from MN

Postby oldestof11 » Mon Oct 27, 2014 3:07 pm

Welcome!

I like that topper. :cool:
Jon
93 D250~ Mismatch of cheap parts, trying to look fast going slow
User avatar
oldestof11
14mm rotor
 
Posts: 4147
Joined: Tue Apr 24, 2007 4:46 pm
Location: Northern Illinois
Top

Re: New first gen owner from MN

Postby CumminsPower59 » Tue Nov 18, 2014 7:40 pm

Welcome! I can tell the body has some rust issues, back of the cab appears to be really sagging from lack of support...
Ike

91 W350 SRW, 3.07's, NV4500, 370's, THD LPPP, Super HX40, 2nd gen IC swap, BHAF, Isspro's, 2" lift, 285's on 3rd gen 17"'s.
04 VW Jetta Wagon TDI 5speed
CumminsPower59
14mm rotor
 
Posts: 3203
Joined: Mon Feb 25, 2008 8:04 am
Location: The Hawkeye State of 'Murica!
Top

Re: New first gen owner from MN

Postby dazedandconfused » Wed Nov 19, 2014 4:23 am

Welcome, I had one that looked just like it. I scrapped it and put the engine in my half ton.
Big Andy
1983 Dodge D150 that has been repowered with a 93 Cummins/518 running gear AKA The Ugly Duck! I would much rather build them then buy them.[
User avatar
dazedandconfused
14mm rotor
 
Posts: 6119
Joined: Thu Apr 05, 2007 6:25 pm
Location: Walton, Kentucky
Top

Re: New first gen owner from MN

Postby michealsamu » Sun Nov 23, 2014 4:27 am

Welcome......tons of information here....have a fun
:D
michealsamu
smoke screw?
 
Posts: 4
Joined: Tue Nov 18, 2014 6:37 am
Top
Post a reply

Return to Welcome

Who is online

Users browsing this forum: No registered users and 8 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group