Lift Kit

everything but the drivetrain

Moderators: Greenleaf, BC847, Richie O

Lift Kit

Postby collegekid » Sun Jul 24, 2011 7:27 pm

Have any of ya'll lifted your d350/250, I put a western hauler bed on the truck, and the skirting sits too close to the ground for my liking, but I dont want to just lift the back end up, I dont mind a little rake, but want the front and back to be a couple inches higher, and dont wanna lose ride comfort, suggestions?
1992 D350 CC LB 5-spd CTD, 366 GSK, Rotated Fuel Pin, Fuel Screw 1 turn off runaway, Factory Match Pyro and Boost, 4" Diamond eye exhaust, and a broken front sway bar :-)
http://photobucket.com/truckytruck
collegekid
14mm rotor
 
Posts: 535
Joined: Fri May 13, 2011 11:15 pm

Re: Lift Kit

Postby Hansen01 » Sun Jul 24, 2011 7:32 pm

a couple inches, maybe airbags?
i know i can get a set for the rear for 300 bucks brand new around here
1990 dodge W250 cummins 6 speed. 4in diamond eye, a turbo,and a pump :D
Under construction...
Hansen01
14mm rotor
 
Posts: 1125
Joined: Tue May 17, 2011 6:34 pm
Location: Tekamah NE

Re: Lift Kit

Postby collegekid » Sun Jul 24, 2011 7:37 pm

Ive heard the air bags give you a terrible ride, unless I go with kelderman ($$$$$) I know I can do new leafs or even blocks in the rear, my concern is the front
1992 D350 CC LB 5-spd CTD, 366 GSK, Rotated Fuel Pin, Fuel Screw 1 turn off runaway, Factory Match Pyro and Boost, 4" Diamond eye exhaust, and a broken front sway bar :-)
http://photobucket.com/truckytruck
collegekid
14mm rotor
 
Posts: 535
Joined: Fri May 13, 2011 11:15 pm
Top

Re: Lift Kit

Postby Hansen01 » Sun Jul 24, 2011 7:40 pm

one of my buddys got em on his 2006 and as long as you dont keep em fully enflated its not to bad, maybe someone else is runnin em on here
1990 dodge W250 cummins 6 speed. 4in diamond eye, a turbo,and a pump :D
Under construction...
Hansen01
14mm rotor
 
Posts: 1125
Joined: Tue May 17, 2011 6:34 pm
Location: Tekamah NE
Top

Re: Lift Kit

Postby collegekid » Sun Jul 24, 2011 7:44 pm

front and rear?
1992 D350 CC LB 5-spd CTD, 366 GSK, Rotated Fuel Pin, Fuel Screw 1 turn off runaway, Factory Match Pyro and Boost, 4" Diamond eye exhaust, and a broken front sway bar :-)
http://photobucket.com/truckytruck
collegekid
14mm rotor
 
Posts: 535
Joined: Fri May 13, 2011 11:15 pm
Top

Re: Lift Kit

Postby Hansen01 » Sun Jul 24, 2011 7:46 pm

hes jus got em on the rear
i wanna get a set for the rear on mine and an add a leaf for the front but i jus bought some 4in exhaust so now im broke :? and that exspensive paint job that is gonna have to be paid for when its done this week :D
1990 dodge W250 cummins 6 speed. 4in diamond eye, a turbo,and a pump :D
Under construction...
Hansen01
14mm rotor
 
Posts: 1125
Joined: Tue May 17, 2011 6:34 pm
Location: Tekamah NE
Top

Re: Lift Kit

Postby collegekid » Sun Jul 24, 2011 8:18 pm

Ya'll think I could fab up a upper and lower mount, and install air bags up front between the upper and lower control arms to increase ride height, and maybe comfort
1992 D350 CC LB 5-spd CTD, 366 GSK, Rotated Fuel Pin, Fuel Screw 1 turn off runaway, Factory Match Pyro and Boost, 4" Diamond eye exhaust, and a broken front sway bar :-)
http://photobucket.com/truckytruck
collegekid
14mm rotor
 
Posts: 535
Joined: Fri May 13, 2011 11:15 pm
Top

Re: Lift Kit

Postby ciamcoop » Tue Jul 26, 2011 2:05 am

Control arms? Your sig says W250, which is 4x4. D250 is 2wd. Which do you have?
'93 W250LE 4x4 club cab, getrag, denny t, 366 spring, 181/210 cam, bored. 020, KDP, 5x.014's, piston pump, 4" tbe, cold air, 255/85/16s, 3.54's one wheeler peeler
User avatar
ciamcoop
fuel screw!!!!
 
Posts: 142
Joined: Sun Jun 13, 2010 11:35 pm
Location: Central Point, OR
Top

Re: Lift Kit

Postby collegekid » Tue Jul 26, 2011 7:22 am

sorry about that, the truck Im working on is a d350
1992 D350 CC LB 5-spd CTD, 366 GSK, Rotated Fuel Pin, Fuel Screw 1 turn off runaway, Factory Match Pyro and Boost, 4" Diamond eye exhaust, and a broken front sway bar :-)
http://photobucket.com/truckytruck
collegekid
14mm rotor
 
Posts: 535
Joined: Fri May 13, 2011 11:15 pm
Top


Return to Chassis

Who is online

Users browsing this forum: No registered users and 61 guests

cron