1stGen.org

THE place for 1st gens

Skip to content

new stacks??

Off topic/not diesel related

Moderators: Greenleaf, BC847, Richie O

Post a reply

new stacks??

Postby beerboy81 » Thu May 28, 2009 1:14 pm

thinkin abt gettin some new stacks and exhaust.. get em and go to any "muffler shop" or are they pretty much a do-it-yourself job?

fill me in, please :)
Jake

'93 W250 LE '92 CTD/IC GETRAG 5sp. 4x4 4" lift 33x15.50x16 TSL/SX Super Swampers, Pumped up, ASA Mods, cooler tubz, 5" stacks.. 366 hiding in the glove box
User avatar
beerboy81
fuel screw!!!!
 
Posts: 75
Joined: Sun Jan 06, 2008 7:36 pm
Location: Chesapeake Bay, VA.
Top

Postby Richie O » Thu May 28, 2009 5:37 pm

I did mine. I do most of the work to all my stuff. I am not paying 50 bucks an hour for what I can do myself. :D
1989 W250 727, 3.07 L/S, S300, P/S Intercooler, Stans exaust, Pump adjustments, 127k miles,297 hp
1993 W250 extended cab, rag, 4.10 l/s, 6x16's, HTT 62/71/14 piston l/p, Isspro EV series tach, fuel pressure, boost, oil pres, water temp, volt, pryo, 132k/ 301 hp
1992 W250 with NV4500, 3.54's, 16cm 60mm GDS H1C, ground stock cone, Isspro tach, pryo, boost, fuel pressure, slow, rusty, dented,180k
User avatar
Richie O
Administrator
 
Posts: 4171
Joined: Sat May 17, 2008 9:01 pm
Location: New England
Top

Postby Ace » Fri May 29, 2009 6:36 am

I wish I could pay $50/hr. for automotive labor. That would be sweet! ;-)
User avatar
Ace
14mm rotor
 
Posts: 1024
Joined: Thu May 31, 2007 2:10 am
Location: CO
Top

Postby beerboy81 » Fri May 29, 2009 9:36 am

right.. and let me guess, you have every tool in the world you need? :lol:
Jake

'93 W250 LE '92 CTD/IC GETRAG 5sp. 4x4 4" lift 33x15.50x16 TSL/SX Super Swampers, Pumped up, ASA Mods, cooler tubz, 5" stacks.. 366 hiding in the glove box
User avatar
beerboy81
fuel screw!!!!
 
Posts: 75
Joined: Sun Jan 06, 2008 7:36 pm
Location: Chesapeake Bay, VA.
Top

Postby Richie O » Fri May 29, 2009 11:25 am

beerboy81 wrote:right.. and let me guess, you have every tool in the world you need? :lol:



All I need for exhaust is a cut off wheel on a grinder and a welder. I know, not everybody has a welder. I have a fair amount of tools just no garage. :evil:
1989 W250 727, 3.07 L/S, S300, P/S Intercooler, Stans exaust, Pump adjustments, 127k miles,297 hp
1993 W250 extended cab, rag, 4.10 l/s, 6x16's, HTT 62/71/14 piston l/p, Isspro EV series tach, fuel pressure, boost, oil pres, water temp, volt, pryo, 132k/ 301 hp
1992 W250 with NV4500, 3.54's, 16cm 60mm GDS H1C, ground stock cone, Isspro tach, pryo, boost, fuel pressure, slow, rusty, dented,180k
User avatar
Richie O
Administrator
 
Posts: 4171
Joined: Sat May 17, 2008 9:01 pm
Location: New England
Top
Post a reply

Return to Lounge

Who is online

Users browsing this forum: No registered users and 14 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group